Email This

2021 Other 3686: For Sale

Print This
Equipment Specifications
Year 2021
Make Other
Model 3686
Price 354500.00 USD
Location Fargo North Dakota USA
Serial # 210360
Condition
Stock # E00060417
Hours 0
Detailed Description

Category For Sale, Status On Yard, Class Used, Available Immediately

Notes
  • VALE/EAGLE 3686 PUG MILL PLANT EQUIPPED AS PER BELOW:PLANT DESIGN:- CARRIES EIW 36" X 8-6" PUG MILL MIXER AND ACCESSORIES - PUGMILL AND WATER PUMPS SUPPLIED BY DEALER AND INSTALLED BY VALE- 750 TONS/HR DISCHARGE CONVEYOR- QTY. (2) TWO 50-400 TONS/HR FEEDER- BASED ON 100 PCF MATERIALPLANT STRUCTURE AND HIGHWAY TRANSPORT:- W21 MAIN BEAMS AND PRIMARY CROSS MEMBERS- PUGMILL MOUNTED TO CHASSIS SUPPORT POINTS- HSS AND ANGLE STRUCTURE HOPPER SUPPORTS- 6 BLOCKING LEG POSITIONS AND 2 FOLD-DOWN LEGS- TRIDEM AXLE WITH DUAL 11R22.5 TIRES HUTCH SUSPENSION- 5TH WHEEL PIN AND TOWING BAR- AIRE BRAKES LIGHTS RELECTIVE TAPE MUD FLAPS- CABLE HANGERS9YD3 HOPPER AND 6YD3 HOPPER:- 1/4" PLATE HOPPER WALLS- 75 DEGREE FRONT AND BACK WALL ANGLES 60 DEGREE SIDE WALLS - INTEGRAL VIBRATOR MOUNTS- MATERIAL FLOW SELF-RELIEVING PROFILE AT SKIRT LEBEL- ADJUSTABLE DISCHARGE GATE- SKIRT EXTENSION PAST HEAD FLOW GUIDE ONTO DISCHARGE CONVEYOR- CANOE LINERS 1.5" X 7" WITH 45 DEGREE TOP ANGLE BACK AND FULL LENGTH HOPPER SIDES - INCLUDING SKIRT EXTENSION TO HEAD PULLEY- STRUCTURAL SUPPORT COLUMNS AND HORIZONTAL MEMBER BRACING- BOLT TO CHASSIS I-BEAMS PICK OFF FOR FEEDER CARTRIDGE MAINTENANCE30" X 11- FEEDERS:- 30" BELT 375 3 PLY 1/4X1/16 D6 BELT VULCANIZED- 12X32 HEAD DRUM PULLEY HERRINGBONE LAGGED 1045-307 SHAFTING 215 SCM BEARING UNITS- 12X32 WING TAIL PULLEY WITH SCREW TAKE-UP 1045-215 SHAFTING 207 SCM BEARING UNITS GUARDED- 10 HP WEG 460V ELECTRIC MOTOR DRIVE WITH DODGE TA4207H40 REDUCER V-BELT DRIVE WITH GUARD- PPI C5 IDLERS 10" SPACING - RUBBER DISC RETURNS 2- REMOVABLE CHANNELCARTRIDGE STRUCTURE GUARDS FOR TAIL AND IMPACT AREAS- SUPERIOR BELT CLEANER URETHANE BLADE AND TENSIONER- FIXED HEAD END- C8 CHANNEL FRAME CARTRIDGE MAINTENANCE REMOVABLE36" X 38- DISCHARGE CONVEYOR:- 330/3 PLY 3/16 X 1/16 D0 BELT VULCANIZED- 14X38 HEAD DRUM PULLEY 3/8 LAGGED 1045-307 SHAFTING 215 SCM BEARING UNITS- 12X38 WING TAIL PULLEY WITH SCREW TAKE-UP 1045-215 SHAFTING 207 SCM BEARING UNITS- 15 HP WEG 460V ELECTRIC MOTOR DRIVE WITH DODGETA3203H15 SHAFT MOUNT REDUCER WITH BACKSTOP V-BELT DRIVE WITH GUARD- PPI C5 CHANNEL INSET IDLERS - 35 DEGREE TROUGH STEEL ROLL 4- CARRY SPACING & 3 X 1- LOAD POINT - RUBBER DISC RETURNS 10- SPACING- GUARDS FOR TAIL RETURNS BEYOND CHASSIS AT HEAD END- SUPERIOR BELT CLEANER URETHANE BLADE AND TENSIONER- C8 CHANNEL FRAME- PROVISIONS FOR SCALE INSTALLPLATFORM HANDRAIL LADDER TO ACCESS PUG MILL- BASE SCOPE INCLUDES 2- WIDE PLATFORM ON 1 SIDE OF PUG MILL - WITH LADDER AND SAFETY GATE ACCESS- STANDARD DESIGN - CHEKCER PLATE PLATFORM WITH 6" KICK PLATES - 42" HSS 1.5" HANDRAIL WITH MID-RAIL AND POSTS REMOVABLE - SAFETY GATE SELC-CLOSING UP TO 30" WIDE ACCESS POINTSOPTIONS INCLUDED:- HYDRAULIC PACKAGE HONDA GX270 QAE 9 HP WITH ELECTRIC START BACK UP RECOIL 3A CHARGE SYSTEM- RUN-ON QTY. (4) - 58 900 LBS 5X18 RUN-ON LEGS - DUAL COUNTERBALANCE VALVE HARDPIPED - LOCKING PIN WITH FINE ADJUSTMENT - INDIVIDUAL VALVE CONTROL POWERED BY HYDRAUILIC PACKAGE- QTY. (1) TOOL BOX- 3/8" AR 400 HOPPER LINER (BOTH HOPPERS)EAGLE 36" X 8- 6" PUG MILL MIXER- 350-750 TPH/60 RPM SHAFT SPEED- STANDARD EIW GEAR REDUCER- FEED HOPPER- HINGED COVERS OVER MIXING AREA- SPRAY BARS- FLOW METER- EAGLE ARMOR PADDLES- INTERMESHING SHAFTS PROVIDE THOROUGH MIXING OF MULTIPLE MATERIALS- 2 1/2 MAX MATERIAL SIZE- OUTBOARD BEARINGS - SPHERICAL - ROLLER REAR GREASE BEARINGS- WEG 75 HP 1800 RPM 230-460 VOLT 3 PH 60HZ ELECTRIC MOTOR2876-95 3" FRESH WATER PUMP EQUIPPED AS PER BELOW:- 3" CAST IRON WATER PUMP- 15 HP ELECTRIC MOTOR 480V 3 PHASE- WITH WATER MANIFOLD TO FEED PUGMILL FRESH WATER - THIS PUMP IS NOT USEABLE IN A POLYMERE FEED OR CHEMICAL FEED APPLICATION AES ELECTRICAL SWITCHGEAR PANEL EQUIPPED AS PER BELOW:- 36X48 NEMA 3R/4 ENCLOSURE - TO BE PLANT MOUNTED - DRIP SHIELD - CONTROLS TO BE INSTALLED LOW INTHE DOOR - 225 AM MAIN CIRCUIT BREAKER - EXTERNAL LOCKABLE OPERATOR - INSTALLED IN LOWER RIGHT HAND SIDE - MANUALLY OPERATED START UP ALARM HORN- 75 HP PUGMILL MOTOR - 125 AMP CIRCUIT BREAKER - NEMA/IEC RATED SIZE 3 MOTOR STARTER - CONTROLS IN ENCLOSURE DOOR - HOUR METER- 15 HP PUGMILL FEED BELT - 40 AMP CIRCUIT BREAKER - NEMA/IEC RATED SIZE 2 MOTOR STARTER - CONTROLS IN ENCLOSURE DOOR- 10 HP BIN FEEDER BELT #1 - 25 AMP CIRCUIT BREAKER - ABB ACS880 VARIABLE FREQUENCY DRIVE - SPPED POTENTIOMETER - CONTROLS IN ENCLOSURE DOOR- 10 HP BIN FEEDER BELT #2 - 25 AMP CIRCUIT BREAKER - ABB ACS880 VARIABLE FREQUENCY DRIVE - SPEED POTENTIOMETER - CONTROLS IN ENCLOSURE DOOR-10 HP FRONT CONVEYOR - FOR STAND ALONE FEED - 25 AMP CIRCUIT BREAKER - CONTROLS IN ENCLOSURE DOOR- 20 HP FOR PUMP - 60 AMP CIRCUIT BREAKER - NEMA/IEC RATED SIZE 2 MOTOR STARTER - CONTROLS IN ENCLOSURE DOOR - WIRED TO A 3 FOOTPIGTAIL WITH HUBBELL CONNECTOR - PLUG INCLUDED- 750 VA CONTROL POWER TRANSFORMER - (2) 2 AMP PRIMARY SIDE FUSES - (1) 6 AMP SECONDARY SIDE FUSE- WITH 150 FEET OF MAIN POWER CORD.PAINTED GRAPHITE GREY WITH YELLOW GUARDINGGUARDING - WE DO NOT WARRANT THAT MANUFACTURERS›¼À™ GUARDING WILL MEET ALL LOCAL CODES. IT IS THE RESPONSIBILITY OF THE END USER TO HAVE GUARDING CHECKED BY A LOCAL INSPECTOR PRIOR TO STARTUP OF EQUIPMENT OPERATIONS CORRECTIVE ACTIONS AND ASSOCIATED EXPENSE ARE THE RESPONSIBILITY OF THE END USER
Photos
image
Zoom In Zoom Out Refresh

thumb   thumb   thumb   thumb   thumb  
thumb   thumb   thumb   thumb   thumb  
hidden image
Say you saw this 2021 Other 3686 On MachineryLot.com!
Contact Information
General Equipment & Supplies, Inc.
 
Sales Department
4300 Main Ave
PO Box 2145
Fargo, North Dakota 58103
USA
OFFICE CLICK TO VIEW FAX CLICK TO VIEW
TOLL FREE CLICK TO VIEW